• Floor outlets on stages

    Hello Richard The type floor outlets I was speaking of were the thick Brass cover plate with the screw plugs that cover the outlet,when not in use, i was looking for a code that said that if not in use, it has to b...
    sowden
    last modified by sowden
  • Protective rubber glove protection

    Hello Gentlemen, I am an instructor here in Brazil, and in class, electricians always complain that they cannot use the insulating glove in conjunction with the leather glove to perform tasks that require greater &ldq...
    nelsoncanteri
    last modified by nelsoncanteri
  • What PPE Category is Required in Verifying Zero Energy?

    As it pertains to NFPA 70E's requirement of placing a device, piece of equipment etc in a "Electrically Safe State", you turn off a breaker to a light switch or outlet. The next step is to verify via a meter that the ...
    carledge
    last modified by carledge
  • NFPA 20:2019 - Sizing Circuit Breaker from Fire Pump Panel

    We are designing to use a circuit breaker with only magnetic unit trip protection for a single fire pump (without a jockey pump).Should the FRAME of the circuit breaker meet the rated current OR...
    bindim
    last modified by bindim
  • NFPA 101 - Emergency lighting

    NFPA 101 requests 10.8 Lux for emergency lighting. I am just wondering if this applies to large open space too ? if we have 50m2 open plan office, do I still need to achieve the 10.8 lux or a lower lux level is requir...
    mohamed.ehtiawesh
    last modified by mohamed.ehtiawesh
  • powder paint dust collectors

    How often should I have my explosion proof dust collectors inspected for the powder paint booths   Sammy Clayton Enviromental and Safety Administrator Newton Instrument Company 111 East "A" Street Butner, NC...
    sammyc
    last modified by sammyc
  • NFPA 70 Article 314.29 (a)

    So this all started by me speaking out of my ass by telling someone I think the code has a unobstructed distance requirement from the opening of junction boxes, and pulling condulets. They just accepted it, but I deci...
    c.schutter96
    last modified by c.schutter96
  • Custom Temporary Power Outlet Unit

    Hello, I work in a ship yard and we're currently looking into fabricating a portable power outlet unit. Supply: 208VAC 3PH, 100A Feed: 110VAC, 1PH, Various 30A and 60A    The vendor we typically buy them ...
    joshua.burke
    last modified by joshua.burke
  • Relocatable Power Taps

    Hi all. I keep going down the RPT rabbit hole after reviewing NFPA 1, UL 1363, UL White Book, and OSHA. I have come to the conclusion the NEC is silent on RPTs. All the references above seems to say hey, yup...
    carl.mister
    last modified by carl.mister
  • NFPA 70 700.16  Egress Lighting

    Hi, My question is in regards to the second paragraph of 700.16 which states:   "Emergency lighting systems shall be designed and installed so that the failure of any individual lighting element, such as the bur...
    vmazzeffi
    last modified by vmazzeffi
  • Interpretation of NFPA 130: 2017 clause 12.4.1 & 12.4.4

    Question 1: Whether NFPA 130: 2017, chapter 12 requirements are applicable to Trainways (Metro rail Viaduct/tunnels) as mentioned under clause 12.1.1. Please confirm?   Question 2: As per NFPA 130: 201...
  • *Electrical Safety Concerns*

    I thought that I would open up a discussion where viewers of this thread could share what they perceive to be the greatest electrical safety concern that they encounter or perhaps the most frustrating electrical safet...
    Steve Benton
    last modified by Steve Benton
  • i am going to active the deluge system with it and its inside

    i am going to active the deluge system with it and its inside  
    abrar.b
    last modified by abrar.b
  • Can 2 pole breakers supply 2 circuits

    Say for example, you have a 120/240 V, 2 pole, 20 A breaker. Does the NEC allow this breaker to serve 2 separate 120 V circuits?
    tgammonphd
    last modified by tgammonphd
  • MCCBs PPE or Not

    I have had a question for some time about operating molded case circuit breakers with or without PPE.  NFPA 70E states in table 130.5 that under normal conditions it is a low risk of exposure to an arc flash....
    troy.wappler
    last modified by troy.wappler
  • Service Disconnect

    Been having some discussions with other people in the trade, and the subject of Service Disconnects came up in regards to OCP and it's location for dwellings or in general. Some have mentioned that the first OCP devic...
    markselectric
    last modified by markselectric
  • NEC 310.104

    For those who were helpful on this post, Thank You.   Chiefns830 managed to drive me away.   Nothing that I read indicated that homeowners were not welcome to ask electrical questions.
    maynardrf
    last modified by maynardrf
  • 480vac 3ph Power Distribution

    I have a system where we are supplying a skid with 3 VFD/motors. The VFD/motors are each wired to there own fused safety disconnect.  The skid also has a fused disconnect for power supply to a 480/120 transformer...
    marc.gelinas
    last modified by marc.gelinas
  • NFPA 72 Dedicated Function Fire Alarm

    Using ICC 2012 and NFPA 72 2010 edition,  Given an occupancy that is not required to have a fire alarm by 907.2.4 and is sprinklered per 903.2.4 thus contains a dedicated function fire alarm unit for water flow ...
    blalkire
    last modified by blalkire
  • Elevator Recall

    Does Fire Sprinkler riser's water flow switch initiate elevator emergency recall? In NFPA 72 "Table A.14.6.2.4" Typical Input/Output Matrix" shows water flow switch on first or second floor initiate elevator emer...
    zara.mosavat
    last modified by zara.mosavat